Feeding the Line: How Collator Rate Sets Throughput
Most conversations about ammunition inspection start with the inspection station: how precise the weigh cell is, what the camera can see, how fast a sorter reads a headstamp. Those questions matter. But on a real line, the first number that limits output is often set before any measurement happens. A machine can only inspect a case or cartridge that arrives at the right place, the right way up, at the right moment. That is the collator's job, and case collator throughput quietly sets the ceiling for everything downstream.
This post looks at why feed rate belongs in the plan from day one, what to ask about a collator before you buy one, and how the AccuFeed series approaches the problem.
A line runs at the speed of its slowest step
Every inspection line is a chain: feed, then one or more checks, then a pass or fail decision and a bin. The chain can never move more parts per hour than its slowest link. If the feeder presents fewer cases than the inspection machine can handle, the inspection machine waits. If the feeder jams and nobody is standing by, the whole line stops, no matter how fast the measuring equipment is rated.
That sounds obvious, yet it is easy to miss when equipment is bought one piece at a time. A plant may spend months comparing inspection accuracy and repeatability, then treat the feeder as an accessory. The result is a capable machine that spends part of every shift idle, or an operator whose real job becomes clearing jams instead of watching quality.
There are three ways a feeder limits a line:
- Peak rate. The most parts per hour it can present under good conditions.
- Sustained rate. What it actually delivers across a full hopper, a full shift and the calibers you really run.
- Downtime. How often it stops, how it recovers and whether a stop needs a person.
Rated speeds on a spec sheet speak to the first point. The second and third decide what you ship.
What the AccuFeed is rated to do
The AccuFeed product page states the feed rate plainly: "Up to 14,400 rounds per hour. Rated per caliber." That figure applies to every model in the series. The AccuFeed 400, AccuFeed 750 and AccuFeed 1000 are each listed at "Up to 14,400 rounds per hour".
Two parts of that statement are worth reading carefully. "Up to" is a ceiling, not a promise for every component. "Rated per caliber" means the rate depends on what you are feeding, so a plan should use the figure for your caliber and component, not a single number for the whole product line.
The models differ in bowl size, not in speed. In the page's words: "All three bowl sizes (12, 16 and 20 inch) feed at the same rate. The difference is how long they run between fills: the 12-inch bowl holds about 15 pounds of 9mm, around 1,600 cases; the 16-inch bowl about 20 pounds; the 20-inch bowl runs longest unattended."
That distinction matters for throughput. Peak rate is identical across the series, but the time between refills is not. On a line that runs without someone standing by, a bigger bowl means fewer stops to reload the hopper.
Matching the feeder to the machine it feeds
A collator that runs faster than the machine downstream does not raise output. It only fills a chute or forces the downstream machine to cope with parts arriving faster than it can take them. What a line needs is a feeder that delivers a steady supply at the rate the next machine actually uses.
According to the product page, the AccuFeed "matches plate speed to the machine it feeds, shuts off when the hopper runs empty, and tells an AccuSort to pause or refill over a direct link." That link runs both ways in practice: the AccuSort page notes that it "Links to the AccuFeed collator for pause and refill handling" and that "the feeder pauses on a jam or an empty hopper."
Compare the stated rates of the inspection machines a feeder might supply:
| Machine | Stated rate on the product page |
|---|---|
| AccuFeed (all models) | Up to 14,400 rounds per hour, rated per caliber |
| AccuVision 360 | 6,000 to 10,000 rounds per hour, by caliber and configuration |
| AccuWeigh 360 | Starts at 3,600 parts per hour with one weigh cell and scales past 12,000 parts per hour as weigh cells are added |
Read side by side, the table shows why the feeder is rarely the step you want to be short on. The AccuVision 360 runs "Between 6,000 and 10,000 rounds per hour, depending on the caliber and the configuration." The AccuWeigh 360 is modular, rated "starting at 3,600 parts per hour with a single weigh cell and scaling past 12,000 parts per hour as weigh cells are added." A feeder rated up to 14,400 rounds per hour sits above the AccuVision 360's stated range and well above a single-cell AccuWeigh 360, so in those configurations the inspection step, not the feed, sets the line's pace. That is usually where you want the limit to be, because inspection is where the value is.
The modular weigh design is also why feed planning should look ahead. A line that starts with one weigh cell and adds cells later raises its weigh capacity each time. A feeder chosen only for today's single-cell rate may become the bottleneck after the expansion. Planning for the feed rate you will need after growth avoids replacing the front of the line later.
Jams: the hidden throughput killer
A feeder's rated speed means little if it stops several times an hour and waits for a person. Jams are a normal part of moving brass and projectiles through a bowl and chute. What separates feeders is how they respond.
The AccuFeed page describes the jam handling as: "Reverses to clear, remembers the working plate speed, alarms if the jam persists; empty-hopper sensor shuts the feeder off." The FAQ adds: "The feeder reverses to clear it and remembers the plate speed that worked. If the jam will not clear it alarms, and if it is feeding an AccuSort the sorter pauses until the feeder recovers."
For throughput, each part of that sequence does a job:
- Reversing to clear turns many stops into short pauses instead of a call for an operator.
- Remembering the working plate speed means the feeder resumes at a rate that worked rather than starting over.
- Alarming only when a jam persists keeps people focused on the problems that actually need them.
- Pausing the downstream machine prevents a starved or confused machine from running empty.
The Technology page ties this to unattended running: "Anti-jam feeding and hopper options let a system be loaded once every eight to twenty-four hours and left to run." Sustained output over a shift depends far more on that behavior than on a peak rate measured in a short run.
Caliber changeovers count too
Throughput is also lost between jobs. A line that runs several calibers loses production every time it changes parts. The AccuFeed page says plates "swap by finger holes in a minute," that "one caliber kit (shell plate and chute)" is included, and that "Twenty-one calibers are on the shelf, from .380 to 9.3x62; others are made to order." Projectile plates and live-round feed kits are listed as available.
When you plan capacity, count changeovers per shift and the time each one takes, then subtract that time from the hours the line actually runs. A short changeover keeps more of the shift for production.
Questions to ask before you size a feeder
Whatever equipment you are considering, these questions turn a spec sheet into a capacity plan:
- What rate is stated for my caliber and component? A rate "rated per caliber" should be checked against the parts you actually run.
- What is the slowest machine downstream, today and after planned expansion? Size the feed for the line you expect to have, not only the first module.
- How does the feeder handle a jam? Ask whether it clears itself, alarms or simply stops.
- How long does it run between fills? Bowl capacity decides how often someone has to reload the hopper.
- Does it talk to the next machine? A feeder that can pause a downstream machine avoids running that machine empty.
- How fast is a changeover? Count plates, chutes and the minutes each swap takes.
- Will it fit the layout you already have? The AccuFeed lists a "Dillon-style mount or mast mount", so it "drops in where a Dillon feeder would go."
Why this matters for quality, not just speed
A feed problem is also a quality problem. When a line is starved or stopping often, operators are tempted to push the line harder, skip a check or move to sampling to catch up. Every one of those shortcuts raises the chance that an out-of-spec round reaches a box. A steady, self-clearing feed protects the reason the inspection equipment was bought: to check every round, every shift, without cutting corners when the schedule gets tight.
That is why feed, sort, weigh and vision are designed as a platform. As the Technology page puts it, "Feed, sort, weigh and vision all share a platform, so a line grows one module at a time." The feeder is the first module, and it decides whether the rest of the line can do its job.
Plan the line from the front
If you are planning a new inspection line or trying to get more out of an existing one, start with the feed. Know your calibers, your components and your volume per shift, then match the collator to the machines downstream. The AccuFeed page is clear that "Calibers, components and volume per shift are enough to start."
Ready to size a feeder for your line? Contact Ammo Inspector with your calibers, components and target volume, and we will help you spec a standard configuration or a custom build.