Home/News/Brass sorting

Sorting Lookalike Cases by Length: AccuSort 250 Camera

Ammo InspectorNovember 18, 20267 min read

Most brass sorting starts with the headstamp, and for good reason. The stamp on the case head tells you who made it, often the caliber, and sometimes the lot. But some of the cases that cause the most trouble look nearly identical from the bottom. A case can carry one caliber's headstamp and be a different cartridge entirely, or carry the right headstamp and still be the wrong length for the next step in the process. For those cases, the camera needs a second point of view.

This post covers why case length sorting matters, where headstamp-only sorting reaches its limit, and how the AccuSort 250 adds length to the sort.

When the headstamp tells the wrong story

A headstamp is stamped into the case head when the case is made. It records where the case started, not what has happened to it since. Once brass is fired, collected, processed and sometimes reformed, the stamp and the case can disagree.

The clearest example is reformed brass. .300 Blackout cases are commonly formed from 5.56 or .223 brass. The case is cut down and reshaped, but the head, and the stamp on it, stays the same. Seen from below, a reformed .300 Blackout case can look just like the 5.56 case it came from. A sorter that reads only the headstamp has no reason to treat them differently.

That matters because the two do not belong in the same bin. Our post on preventing mixed-caliber ammunition covers why a wrong round in the box is a serious safety problem, and why "it fits" is not the same as "it is safe". The short version for a sorting operation: lookalike cases have to be separated before they reach loading, because the risk only grows once they are assembled into cartridges.

Length is a separate measurement

Headstamp recognition and length measurement answer different questions:

  • Headstamp recognition answers "what does the case head say?" It sorts by brand, primer size, Berdan or Boxer, and caliber where the stamp shows it.
  • Length measurement answers "how long is this case right now?" It sees what the stamp cannot: a case that was cut down, reformed, or stretched by firing.

Neither replaces the other. A headstamp library groups cases by maker and type. A length check catches the cases whose history has changed their dimensions. Together they give a much more complete picture of each piece of brass than either one alone.

How the AccuSort 250 adds length to the sort

The AccuSort series reads the headstamp on every case with a machine-vision camera and matches it against a library trained on your own brass. The product page describes how the 250 builds on that: "The 250 adds a side-view camera so it sorts by case length as well, which separates .300 Blackout from reformed 5.56 and screens trim length."

In the model table, the AccuSort 250 is described as "AccuSort 200 plus a side-view camera: sorts by case length too." That means the 250 keeps everything the 200 does as a production sorter, including the rotary selector over a ring of bins, and adds a second view of the case from the side.

The specification lists the sort criteria across the series:

  • Brand (headstamp)
  • Primer size, large or small, "better than 98 percent"
  • Berdan or Boxer
  • Caliber "within a 2:1 length range"
  • Steel and aluminum by colour
  • "Case length on the AccuSort 250"

Length is the one criterion on that list that only the 250 provides. If your incoming brass includes reformed cases, or you need to screen cases by length before they go further, that is the model built for it. The site sums up the lineup this way: "The 200 is the production machine, the 250 adds length sorting, and the 300 is for the highest volumes when calibers rarely change."

Two jobs for a length camera

Separating lookalike cases

The first job is the one described above: telling a reformed .300 Blackout case from the 5.56 case it looks like. The headstamp read says one thing, and the side view shows the case is a different length. The sorter can then send it to its own bin instead of mixing it in with full-length brass.

This is useful anywhere mixed brass comes in from outside: range pickup, once-fired brass bought in bulk, or returns from customers who load more than one caliber in the same family.

Screening trim length

The second job is screening trim length. Cases stretch when they are fired, so brass that has been fired and processed can come back longer than it started. The AccuSort page lists the 250 as a machine that "screens trim length", and its "Who runs it" section notes that competition shooters and reloaders use it to "keep match brass by headstamp and lot, and screen reformed cases by length."

For a processor or remanufacturer, screening length at the sorting stage means cases that need attention are found before they reach the processing line, rather than at a later station where a stop costs more.

Know the operating range

A length camera is only useful inside the range the machine is built for. The AccuSort specification lists cases from "9mm to .308 length, up to 0.5 inch diameter," clean or dirty, primed or deprimed.

Two other points from the product page are worth planning around:

  • Mixed calibers in one run. "Mixed calibers sort in one run within a 2:1 length range (9mm and .380 together, for example); beyond that, pre-sort by size with a trommel or slotted basket first."
  • Plated cases. "Some plated cases look like brass to the camera, so a small share can pass as brass." Steel and aluminum are caught by colour, but plated cases are a known edge case.

Specifications describe standard configurations. The page notes that "Calibers, component sizes and throughput outside these ranges are quoted as custom builds."

Accuracy, unknowns and the second look

Length sorting sits on top of the same headstamp engine as the rest of the series, so the same accuracy rules apply. The site states accuracy of "up to 99.99 percent with a well-trained library," and adds a trade-off worth understanding: "Raising the accuracy target raises the share of good cases set aside for a second look."

That is a choice each operation makes. A line feeding match-grade loading may accept more cases set aside in exchange for a cleaner output bin. A high-volume processor may tune the other way.

Unknown cases are handled conservatively. According to the specification, "Unknown headstamps pause the machine for the operator and are added to the library." The library starts in learning mode and moves to automatic as it fills in. The system also "runs without an internet connection," which matters on production floors that keep equipment off the network.

Feeding and what comes next

A sorter only works on the cases it is given. The AccuSort "links to the AccuFeed collator for pause and refill handling," and the feeder pauses on a jam or an empty hopper. If you are planning a full line, the AccuFeed series is the piece that presents cases to the camera one at a time. Our post on how collator rate sets throughput covers why feed belongs in the plan from the start.

Sorting the brass is one step. Inspection of the case and the finished round is another. Dimensional and surface defects on cases are the job of vision inspection, covered in what a virtual case gauge sees and handled on our AccuVision systems. Charge-weight problems are caught by weight, on the AccuWeigh series. If you are still deciding what kind of sorter fits your operation, start with our guide to choosing a brass sorting machine.

Questions to ask before you choose

When lookalike cases are part of your incoming brass, ask:

  1. Do reformed cases show up in your supply? If yes, headstamp-only sorting will not separate them on its own.
  2. Do you need to screen length before processing? If cases that are out of length cost you time downstream, catching them at the sorter is cheaper.
  3. Are your calibers inside the machine's range? Check case length, diameter and the 2:1 rule for mixed runs.
  4. How strict should the accuracy target be? Decide how many good cases you are willing to set aside for a second look.
  5. How will cases be fed? Plan the collator with the sorter, not after it.

Tell us what you load. We will spec the line.

If lookalike cases or trim length are slowing your sort, we can help you work out whether the AccuSort 250 fits your brass and your volume. Send us your calibers, components and volume per shift, and we will reply by email, usually within one business day. Request a quote.

More from the shop floor

Tell us what you load. We will spec the line.

Request a quote